DTC reference · Free definition

P0301 : cylinder 1 misfire detected

It indicates that the computer has detected an anomaly in the combustion of the cylinder concerned and the ignition, injection and compression systems.

You have P0301 on your vehicle?

Cross-reference this code with your vehicle, symptoms and other faults to prioritize possible causes and choose the first checks.

Analyze P0301 on my vehicle

2 standard diagnostics offered with the Discovery account · Without a bank card
For all new Discovery accounts.

Meaning

What does this code mean P0301 ?

The code P0301 indicates misfires on cylinder 1. It does not by itself indicate a faulty coil, injector or other part. The freeze frame data and the associated faults make it possible to put the failures back into their original conditions. The numbering of cylinder 1 must be checked in the vehicle documentation.

The definition is generic, but the actual architecture may have multiple rows, sensors, channels, or actuators. The indications present in the wording must be linked to the vehicle diagram to avoid checking the wrong component.

An electrical fault can reproduce the effect of a mechanical anomaly and vice versa. The diagnosis must therefore compare the measurements to physical reality and take into account the other recorded codes.

Read the full presentation and summary

Code P0301 corresponds to the following fault: Cylinder 1 misfire detected. It indicates that the computer has detected an anomaly in the combustion of the cylinder concerned and the ignition, injection and compression systems. The code describes the result of monitoring, but it does not alone identify the responsible part.

In vehicle operation, this system must maintain regular and balanced combustion on all cylinders. An inconsistent electrical value, a command that does not reach its setpoint or an abnormal mechanical condition can therefore produce the same code.

This sheet is an orientation aid. Component locations, detection thresholds and measurement procedures vary by make, model and engine. Fixed data and manufacturer documentation must guide the checks.

P0301 reports the following fault: cylinder 1 misfire detected. The analysis must confirm the appearance conditions, check the circuit concerned and compare the setpoint to the actual values ​​before any replacement decision.

Limits

What the code P0301 does not allow us to conclude

This code does not, on its own, confirm the faulty part or the repair to be carried out. The associated defects, the conditions of occurrence, the vehicle concerned, measurements and physical checks remain necessary to confirm or rule out a cause.

Symptoms

Possible symptoms

  1. 01

    Engine shaking or lacking power

  2. 02

    Engine light flashing during severe misfires

  3. 03

    Difficult starting or stalling

  4. 04

    Engine light or fault message on

  5. 05

    Degraded operation when protection policy is enabled

  6. 06

    No constant symptoms when the fault is intermittent

  7. 07

    Irregular operation under conditions where the fault is detected

  8. 08

    No obvious symptoms when the anomaly remains intermittent

Causes

Possible causes

  1. 01

    Component slow, drifting or incapable of reaching the set point under the monitored conditions

  2. 02

    Faulty spark plug, coil or injector

  3. 03

    Insufficient compression or mechanical cylinder defect

  4. 04

    Incorrect air fuel mixture or air intake

  5. 05

    Oxidized, poorly locked or contaminated connector

  6. 06

    Harness cut, rubbed, short circuited or exhibiting parasitic resistance

  7. 07

    Incorrect power, ground or reference voltage

  8. 08

    More rarely, calibration or internal fault of the control module

Which causes should you check on your vehicle? Cross-reference these possible causes with your symptoms and other faults.

Analyze P0301 on my vehicle

Controls

Checks to consider

  1. 01

    Read all codes and keep freeze frame data before clearing them

  2. 02

    Compare the command, feedback signal and physical value to the manufacturer's specifications

  3. 03

    Compare misfire counters between cylinders

  4. 04

    Swap components when the procedure allows

  5. 05

    Check ignition, injection and compression

  6. 06

    Read the associated codes and keep the freeze frame data before any erasure

  7. 07

    Identify the component, the channel and the row with the manufacturer's documentation

  8. 08

    Inspect the component, its connectors and the harness routing

  9. 09

    Compare the setpoint, the actual value and the available electrical signals

  10. 10

    Validate the correction under the conditions of appearance of the fault

Pitfalls

Common pitfalls

  1. 01

    Immediately replace a component based only on P0301

  2. 02

    Clear the fault before having saved the exact conditions of its appearance

  3. 03

    Confusing an abnormal electrical value with evidence of a mechanical failure

  4. 04

    Check wrong row, wrong sensor or wrong actuator

  5. 05

    Neglecting the condition of the harness, connectors, power supplies and masses

  6. 06

    Using generic values without checking vehicle specifications

  7. 07

    Ignore associated codes that may reveal the common cause of the fault

FAQ

Frequently asked questions about P0301

Does the code P0301 designate a part to be replaced?

No. It describes an anomaly detected by the computer. Electrical, mechanical checks and data comparison are necessary to identify the probable cause.

Can we continue to drive with P0301?

It depends on the symptoms and the system involved. A significant loss of power, stalling, overheating, leaking or abnormal noise warrants stopping use and having the vehicle checked.

Why is hard data important?

They indicate the speed, load, temperature and other values ​​present during detection. They make it possible to reproduce the fault conditions and avoid random replacements.

Can the P0301 code come back after erasing?

Yes. If the cause remains present, the computer will memorize the fault again when its monitoring criteria are met. Erasure alone does not constitute repair.

Sources and method

An orientation sheet, to be placed in the context of the vehicle

This sheet distinguishes the meaning of the code, the symptoms and possible causes, then the checks to consider. When a specific source is used to support information, it must be visible on the page. No diagnosis is guaranteed without verification on the vehicle.

Consult the editorial method of Diagolia.

Diagolia

Analyze P0301 in the context of your vehicle

Cross-reference this code with your vehicle, symptoms and other faults to prioritize possible causes and choose the first checks.

2 standard diagnostics offered with the Discovery account · Without a bank card
For all new Discovery accounts.

Analyze P0301 on my vehicle